The Basics of Plumbing Skills When Installing a Bathtub
The Basics of Plumbing Skills When Installing a Bathtub
Blog Article
This great article listed below relating to A Step-by-Step Guide to Installing a Bathtub is exceedingly entertaining. Don't overlook it.
Installing a tub isn't precisely rocket science, yet it does call for strong plumbing, woodworking, and sometimes, tiling skills. Changing an old tub with a brand-new one is additionally a moderately difficult task. If the old bathtub is conveniently easily accessible, the project can relocate quickly; if you need to open up a wall to remove the old tub and position the new bath tub, the job is much harder. In either instance, the project is within a home handyman's skills, although you will certainly need an assistant to move out the old tub and also set in the new one. See to it you have actually certified yourself for the task and fit attempting it. Instead of working with a contractor to take over a halfway-completed job, it is better to think about employing one before you begin. Chances are you might need a specialist plumber to make tube connections.
This write-up will assist you install a new bathtub in your washroom if you have actually already acquired a brand-new bathtub and also don't require to alter the arrangement of your previous supply of water pipes.
Your tools as well as product list need to comprise the following:
Removing Old Touches
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you must do is disconnect the water supply. After doing so, switch on the faucets to drain pipes any kind of water continuing to be in the system. The process of removing the existing taps can be quite problematic because of the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a faucet device to undo the nut that attaches the supply pipelines to the faucets. Have a fabric ready for the continuing to be water that will certainly originate from the pipes. As soon as the supply pipelines have actually been removed, utilize the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning throughout this process. As soon as the taps have been gotten rid of, the holes in the bath/basin will have to be cleaned of any old securing compound.
Prior to moving on to fit the brand-new taps, compare the pipe links on the old taps to the brand-new faucets. If the old faucets are longer than the brand-new faucets, then a shank adapter is required for the brand-new taps to fit.
Suitable New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic connector to prevent damages to the thread. One end of the connector fits on the plastic tail of the faucet as well as the other end offers a link to the current supply pipes.
If you need to fit a monobloc, after that you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washers are in area in between the tap as well as the sink. Safeguard the tap in position with the maker offered backnut. Once the tap is safely in position, the supply pipes can be connected to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with normal faucet ports. The former type must be linked to the tap finishes first, tightening just by hand. The supply pipelines can later on be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been attached.
Installing the Tub
Using the two wooden boards under its feet, place the bathtub in the called for setting. The wooden boards are useful in equally spreading the weight of the tub over the area of the boards rather than focusing all the weight onto 4 tiny points.
The following objective is to ensure that the bathtub is leveled all round. This can be attained by examining the level and also changing the feet on the tub until the spirit level reviews degree.
To set up faucets, fit the bottom of the outermost adaptable tap adapter to the suitable supply pipeline by making a compression sign up with; then do the exact same for the various other faucet.
Switch on the supply of water and examine all joints as well as brand-new pipework for leaks and also tighten them if needed. Load the bathtub as well as likewise inspect the overflow electrical outlet and the normal electrical outlet for leaks.
Finally, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and sealing around the tub should wait until the bathtub has been made use of a minimum of once as this will resolve it right into its final placement.
Getting ready for the Installation
First of all, the sustaining framework provided with the bath should be fitted (if needed) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to see to it that if the tap comes with a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is likewise practical to fit a supporting plate under the taps unit to prevent stress on the tub.
Fit the flexible faucet adapters to the bottom of both faucets utilizing 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet via the hole in the bath. Make use of the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you utilize all of the provided washers.
Link the trap to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be suited its last position.
Tiling Around the Tub
In the location where the bathroom meets the tile, it is required to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate enough to split an inflexible seal, causing the water to permeate the wall in between the bathroom and also the tiling, leading to difficulties with moisture as well as possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your components as well as fittings. They are sold in tubes and also cartridges, and also are capable of sealing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Remember to always load the bath tub with water prior to sealing, to permit the activity experienced when the tub is in usage. The sealant can split fairly very early if you do not think about this motion prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are additionally easily offered on the marketplace. It is advisable to fit the tiles making use of waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am very taken with A Step-by-Step Guide to Installing a Bathtub and I'm hoping you enjoyed the entry. Liked our piece of writing? Please share it. Help other people locate it. I enjoy reading our article about How to Install a Bathtub Yourself.
Get instant help, call now! Report this page